UV Curing Machine for Shoe Paint

UV Curing Machine for Shoe Paint

This is a UV curing machine for shoe paint. As we all know that drying is a vevry complex physical and chemical process. This proess is relatively long. If UV curing is used, the cured materical can be dried in a short time, which greatly saves the time of natural dring and improves the production efficiency.

  • Model:LDUVJ-7D-21KW
  • Power:380VAC 50Hz
  • Size:3000L X1000W X1700H mm
  • Wavelength:365Nano
  • Application range:Shoe paint curing / trademark printing
  • Product Description
  • Customer Question & Answer

UV Curing Machine for Shoe Paint

鞋子3kw7组灯uv固化机4.jpg


Product name
UV curing machine for shoe paint
Product numberLDUVJ-7D-21KW
Equipement size 3000L X1000W X1700H mmPower supply
380VAC 50Hz
Power about 21kw
Belt width600mm
Transmission rate0--10m/min
Belt materialStainless steel
Light source configuration3kw*7lamps,air-cooled lamp holderMain crest length365(Nano)
Power regulation50%--100% Application rangeShoe paint curing / trademark printing


鞋子3kw7组灯uv固化机5.jpg


Product characteristics 

   

   The conveyor belt speed of this machine is adjustable,the UV lamp is equipment with two gears,the illumination area of the lamp

holder can be up, left and right can be adjusted, and seven sets of lamps are equipment with all-directional illumination curing, and the emergency stop button is equipment beside the inlet and outlet ports. The equipment has the charateristics of automatic detection and alarm system, convenient maintenance,golden durability and so on. 



     鞋子3kw7组灯uv固化机1.jpg



鞋子3kw7组灯uv固化机2.jpg


鞋子3kw7组灯uv固化机6.jpg


Application range

鞋子3kw7组灯uv固化机应用行业.jpg

Product precautions


1. Before using this uv curing machine, please read the instructions in detail;

2. Do not look directly at the uv lamp and the light source for a long time, otherwise it will burn your eyes;

3. High voltage electricity danger;

4.When repairing and replacing parts, please turn off the main power supply, replace the uv lamp tube, and discharge the stored power of the capacitor;

5. Do not put your hands on the transmission part to avoid danger;

6. When testing the machine, please check whether the phase sequence of the fan is correct.


About UV machine product repair and maintenance


1. In order to prolong the service life of the uv equipment and ensure the normal operation of the equipment, the equipment should be checked before starting up, and the problems should be corrected in time.

2. Start running continuously for half an hour. Observe whether the indicators and indicators are normal, and whether there is any abnormal sound during operation. If abnormalities are found, check immediately.

3. Clean the panel at least once a month and check whether the screws of each part are loose.

4. Avoid touching the lamp tube with your hands to prevent sweat and oil from affecting the ultraviolet light transmission. If it is accidentally contaminated, it can be wiped clean with alcohol cotton.

5. The lamp tube and reflector should be wiped with alcohol once a month to keep them clean. If the surrounding environment is bad, increase the number of cleanings accordingly.

6. The exhaust fan should be cleaned every three months to clean the fan blades, the outside of the casing and the appearance of the motor.

7. Add lubricating oil to each rotating part of the fan, adjust the air valve drive mechanism, tighten each terminal, and check whether the air valve drive mechanism is flexible and reliable, and whether the wires are damaged.

8. If the small uv curing machine is not used for a long time, it is advisable to loosen the conveyor belt to make it in a free state.

9. After a period of use, the transmission chain will naturally extend and should be adjusted in time. During the use of the conveyor belt, due to temperature changes, there may be deviations, and should be adjusted in time.

10. Ensure the lubrication of the movable parts of the small uv curing machine. The active and passive rollers, bearings, chains and transmission wheels should be greased every six months; other parts and motors should be greased once a year.

11. After each use of the small uv curing machine, clean up the dirt and dust to ensure that the mesh belt runs freely.

12. Frequently check whether the plug of the small uv curing machine is in good contact with the socket. For example, when the price of the small uv curing machine is running normally, if the cable is found to be hot and hot, we must stop it.

13. The electrical wiring inside the machine must not be changed at will. In the event of a malfunction, check and repair in time, and non-professional maintenance personnel are not allowed to disassemble or replace it without authorization.


about landun.jpg


公司简介1.jpg


Why choose us?


1. Adopt stepless adjustable technology, with adjustable energy, one-key standby function, saving unnecessary energy consumption.

2. Passed the EU ce certification, won the title of Guangdong High-tech Enterprise, and each machine passed strict testing.

3. Recognized by more than 2000 customers, product applications in 60 different industries, 16 patented inventions, member of China Radiation Curing Association.

4. Lifetime free technical support, so that customers can enjoy good after-care services make our duty.


Certificate


证书.jpg